Wema Fuel Gauge Manual Dexterity. However, for racing purposes, it is overly large and heavy. That is where aluminum fuel cells/. All right guys, fuel gauge isn't working. I'm suspecting the fuel sending unit but do a little bit testing here to show you. You can see how the fuel's on Empty. Find great deals on. Explore Ghad Arddhu's board 'Moroni' on Pinterest.| See more ideas about Black, Character art and Character ideas. Loading Frequently Asked Questions General Q: Does Wema USA have a CAGE code? • Yes, our CAGE code is 6V6U1 Q: Do you ship overseas? • Yes, you can place the order directly through our website, or you can email us at to place your order. Q: We are a distributor, how can we setup an account with you? • Please contact us at in order to be setup as a distributor. Q: What is your warranty policy? • The SSS/SSL, S3U, S5U sender models have a limited 3 year warranty. • SHS/SHST holding tank senders have a limited 2 years. • All the gauges have limited 18 months warranty. Q: What is your return policy? • Please see our regarding product return policy. Technical Trouble Shooting Q: Why is the level gauge reading backwards (reading full when tank should be empty, reading empty when tank should be full)? • That means the gauge and the sending unit are using different standards (one may be using American standard, 240 ohm at empty, 30 ohms at full; the other may be using European standard, 0 ohms empty, 180 ohms at full), hence, are not compatible. • Only solution would be to replace either the gauge or the sending unit so that both are using either European Standard or American Standard ohm range. Q: Does Wema carry a fuel sender that can be shortened in length? • Yes, the length of the High Resolution Capacitance Level Sensor (CLS) can be shortened and signal output re-calibrated. Q: What lengths do the standard units come in? • SSS/SSL • Available 4' through 18.5' at 0.5' increments • Available 19' through 60' at 1' increments • S3U and S5U • Available 4' through 60' at 1' increments • SHS/SHST • 4', 6', 8', 12', 16', 18', 20', 22', 24', 28', 38' Q: Are the level senders or gauges NMEA 2000 certified or compatible? • Currently the gauges are not compatible with the NMEA 2000 system. The level senders can be made compatible by connecting it to a signal converter module. Sending Units Q: What are the signal outputs of the level senders? • The signal output for our stock senders are 240-33 ohms (American Standard). Adobe creative suite 4 cs4 master collection keygen torrent. • For any other output signals (0-180 ohms European Standard, current output, voltage output) please contact us at Q: How does the 2 wires from the senders connect? • Black wire connects to the gauge; pink wire connects to the ground. The sender draws power through the gauge connection. Q: What are the senders made of? • The body of the fuel/water/holding tank senders are made of AISI/SUS type 316 stainless steel. Q: How do I determine the length of the sender I need? • For Fuel/Water senders, the length should be 1' less than the depth of the tank if tank is plastic, and 0.5' less than the depth of the tank if tank is metal. This is to account for possible tank flex. • For Grey/Black water holding tanks, the length should be 75% of the depth of the tank. Q: What is the operating voltage for the senders? • The senders can work with both 12V and 24V system. The sender draws power through the gauge connection. Q: How to verify if sender is connected correctly? • Check to see if the sending unit is receiving power from the gauge. The reading at the sending unit will be less than the input voltage at the gauge. • Check the sending unit’s ground. The ground wire must be properly grounded to a common ground, or to the negative on the battery. Q: How to test if sender is operating correctly? • Disconnect the sender wires at the sending unit. • Connect the 2 wires to an ohmmeter or multimeter and set signal to resistance. • Take measurement of the sender at empty and full positions. This can be done by either draining and then re-filling the tank which the sending unit is installed, or remove the sending unit from the tank and then manual operate the float by hand. • For American Standard, the meter will show 240 ohms at empty and 30 ohms at full. For European Standard, the meter will show 0 ohms at empty and 180 ohms at full. Q: Do the senders and sensors work only with Wema gauges? • No, the sender and sensors can work with gauges from other companies as long as both are compatible (both American standard units, or both European standard units). Gauges Q: What are the input signals for the gauges? • The signal input for our stock gauges are 240-33 ohms, American Standard (when applicable) • For 0-180 ohms, European Standards, please contact us at (954)463-1075 or Q: What type of signals does the Tachometer take? • The tachometer can process both sine and square signals. Q: What is the operating voltage for the gauges? • The gauge can work with both 12V and 24V systems. When connecting to a 24V system, certain gauge will require a drop resistor on the connection between the power and the gauge. Q: How to test if the level gauge is operating correctly? • Make sure power to the gauge is not on.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |